针对自动化测试用例的要求(requirement of test case for autotest
一，目的明确，有具体的输入输出
Purpose
以前的目的
Verify if the CDR is right about user order tvod program
修改后
Verify that while TVOD ordered from EPG CDR record created correctly
Input data and out put data shall be described clearly
二，有明确的步骤和检查点
Step
1.MC sigon
2.Enter 'TVOD' at EPG
3.Select one TVOD program
4.Order the tvod program
5.Check the cdr that build by AC
/opt/utoss/accountcenter/chargedata/online/succ
1.Enter 'TVOD' at EPG
2.Select a TVOD program
3.Order the tvod program
4.Open cdr (file) which exists on AC under
/opt/utoss/accountcenter/chargedata/online/succ
5.Check the value pending after tag "7/" matches the service ID
Clear steps and check point
三，准备要求是数据的准备
Precondition
1.OSS is normal
2.Billing of TVOD had config at OSS
3.Have one MC
4.VSLR/PSC/EPG/USC/AC is normal
1 Find or create IPTV subscriber refer to TC IDxxxx1, give UserID
2.Find a TVOD from OSS refer to TC IDxxxx2
3.Get "ServiceID" from "Service" table on OSS db by giving UserID
4.Install new subscriber on MC refer to TC IDxxxx3 or sign on MC refer to TC IDxxxx4
Not environment preparation, it should be detail data preparation to meet this test case needs. (it’s better to refer to test case ID, if it’s too difficult, at least give the test case set path.)
四，预期结果必须细化
Expected Result
1.User can order the tvod program
2.AC can write the cdr after user order the tvod program
1. AccountCenter can write the cdr after user order the TVOD program, there should be a record about the user order the TVOD
2. Check specified field 7 of the cdr, it should eauql to the serviceid of the user
Clearly describe the expected result which matched the output data descript in “Test Purpose”
case 2:
Purpose
NMS support browse chassis inventory inside CO
Verify that chassis inventory shall be browsed on NMS CO Physical View, and chassis id from inventory is matched with chassis id from blade of the chassis
1. Login NMS
2. Open one physical view
3. Browse chassis inventory inside CO
4. Check the result and compare these data with real information
Step
1. Login NMS
2. Open one real CO's s physical view.
3. Browse chassis inventory on CO physical view, select any one chassis, get its ChassisID (SRS or HLD must provide enough information such as “look and view” or operation flow, comments by Norten)
4. Browse blade inventory on CO physical view, select any one blade of selected chassis, get its BladeIP
5. Telnet on the selected blade, get chassis id from /usr/local/rss/chassis_id file
6. Compare the chassis id from inventory with chassis id from blade
Precondition
Master Chassis Manager run normally
NMS run normally
Some NE run normally
At least one real CO and NE is running or create a real CO
Expected Result
1. NMS support to browse chassis inventory inside CO
2. User can check chassisPhysicalID information.
1. NMS support to browse chassis inventory inside CO
2. The chassis id from inventory is matched with chassis id from blade.
(Notice: The chassis id from inventory is in Hex format, the chassis id from blade is in Dec format)
/1 
关于我们
发表于 2007-6-10 16:49:53
!我觉得设计自动化用例的时候，我们是否可以借用其他行业所说的“模块化设计”；我们可以单独分别为登陆、增加、删除、修改设计用例，然后只要组装起来就可以正常使用了！本人的观点而以